@builtnotbought92

We built a motorized DIY mini paddle boat using plastic bottles, a custom wooden crankshaft, and a tiny DC motor with a battery setup! We did it by linking the motor to the crankshaft and wood figure so the passenger actually paddles while driving the side propellers. #diy #Tips #Lifehacks #idea

Tired of everyday boredom? Build this epic motorized water boat! Stop wasting your time scrolling on your phone, let me show you how to easily craft this incredible self powered mini boat using just a few empty plastic bottles! Start by grabbing 2 small plastic bottles bottles and bind them tightly together using a strong rubber band to create the ultimate floating base. Next, take a piece of thick metal wire and carefully bend it to form a rotating crankshaft. Then attach two small round wooden pulleys to make the rear propeller. Grab a blue plastic cap, carve even side slits and use hot glue to secure four small wooden craft sticks as the blades. Mount your crankshaft and propeller between the bottles using sturdy wooden supports. Now build a tiny wooden passenger with movable arms and legs using cut craft sticks and mini screws, topping him off with a tiny blue cap for the engine. Securely mount a rechargeable battery, a red power switch, and a mini electric motor to the back. Use a rubber band to connect the motor to the crankshaft. Finally, link the wooden figure's arms and legs to the shaft so he actually paddles! Turn it on and watch it race across the water! Comment boat for more awesome hacks!

We built a DIY rapid-fire coin shooter using craft sticks, a bottle neck magazine, rubber bands, and a T-handle slider! We did it by assembling a wooden track with a top-loading coin chute and a rubber band–tensioned pusher to launch coins continuously. #diy #Tips #Lifehacks #idea

Tired of everyday boredom? Build this epic rapid fire coin shooter! Stop wasting money on useless plastic toys! Let me show you how to easily craft this incredibly fun pocket sized gadget right at home! Start by gluing six wooden craft sticks side by side to create a solid rectangular base. Next, place a coin in the center and use it as a guide to glue two extra sticks on the outer edges. This creates a perfectly smooth internal track for your ammo. Now carefully cut off the threaded plastic neck from an empty water bottle. Secure it firmly to the front of your track, using hot glue to act as your ammo magazine. To make the firing mechanism, cut and glue one stick across another to form a strong T shaped pulling handle. Slide it smoothly into the back of your track. Add a tiny plastic ring at the back, then grab a durable rubber band, loop it around the front plastic neck, and stretch it tightly back to hook onto both sides of your handle. Load up your coin magazine, pull back and release to instantly blast away your boredom. Comment shooter for more awesome hacks!

We built an emergency electronic spy igniter using an AA battery, thick copper leads, and coiled nichrome wire wrapped in cotton! We did it by connecting the battery to pass current through the high-resistance nichrome spring, heating it to red-hot ignition temperatures instantly. #diy #Tips #Lifehacks #idea

Build a secret spy lighter using just one standard battery. Stop relying on cheap plastic lighters that always run out of fluid. Let me show you how to easily craft this incredible pocket sized gadget inspired by secret spy movies using a few basic items. Start by grabbing an ordinary AA battery. Take a thick piece of bare copper wire and cut it into two equal sections. Use pliers to carefully remove any plastic insulation from the ends of both copper pieces. Now apply a thick drop of hot glue to mount the first wire securely onto the top positive terminal. Attach the second wire exactly the same way to the bottom negative terminal. Next, get a spool of extremely thin nichrome wire. Carefully wrap this delicate wire around a small wooden toothpick to form a tight, tiny mess. Metal spring. Securely twist the ends of this tiny nichrome spring between the two exposed copper wires to complete your basic electrical circuit. To test out your secret gadget, take a small piece of cotton and wrap it gently around the center spring. Once the electrical current flows, the thin metal wire instantly glows red hot, quickly igniting the cotton into a surprisingly powerful flame. Comment Spy Eye for more hidden gadgets.

We built a DIY wearable wrist launcher using rolled paper tubes, rubber bands, and a mask string! We did it by mounting a spring-loaded paper barrel assembly onto a wrist base with a finger-triggered string release mechanism. #diy #Tips #Lifehacks #idea

We built an emergency battery-powered spark generator using a AA battery, a rocker switch, and a drywall screw! We did it by wiring the battery through the switch to create intense electrical sparks when scraping a second screw against the terminal. #diy #Tips #Lifehacks #idea

Turn a standard battery into a survival fire starter. Stop worrying about getting stuck in the cold without matches. Let me show you how to easily build a powerful emergency spark generator using basic items you already have. Start by grabbing an ordinary AA battery and a sharp black drywall screw. Apply a thick drop of hot glue directly to the top positive terminal and mount the black screw standing perfectly upright. Next, take a mini white rocker switch, add some hot glue to the back, and press it firmly against the side of your battery. Now take a short piece of insulated copper wire and carefully strip both ends to expose the metal. Use hot glue to secure one bare copper end directly to the bottom negative terminal. Connect the other end of that exact same wire to the first pin on your switch. Grab a second wire, attach it to the other switch pin, and wrap the exposed copper tightly around the bottom threads of the black screw to use it. Flick the switch on. Grab a loose silver screw and aggressively scrape it against the black one. This instantly generates intense electrical sparks, easily igniting a cotton pad to start a blazing campfire. Comment fire for more hacks.

We built a DIY wearable toothpick shooter using parts from a click pen and a plastic bottle ring! We did it by mounting the spring-loaded pen mechanism onto the ring base to create a hidden finger-mounted launcher. #diy #Tips #Lifehacks #idea

Or at your desk and looking for a fun way to pass the time. Stop wasting money on cheap plastic toys! Let me show you how to build a powerful hidden toothpick shooter you can wear on your finger. Start by grabbing a standard clickable ballpoint pen. Completely disassemble the pen to extract the metal spring and the small plastic clicking mechanism inside. Next, take a sharp utility knife and cut off a small section of the clear plastic pen tube. Carefully carve tiny side slits into this tube to hold your firing mechanism safely in place. Now modify the blue plastic clicker by trimming down its edges so it slides perfectly smooth. Attach the metal spring securely between this blue piece and the clear plastic tube to make the wearable base. Grab an empty plastic bottle and slice off the plastic ring located right below the cap. Apply a drop of hot glue and mount your pen mechanism directly onto this ring. Your secret mini gadget is now completely ready. Slide the ring onto your finger and load a wooden toothpick. Pull back the blue slider, take aim and release to instantly launch your dart and pop a balloon. Comment shooter for more awesome DIY hacks!

We built a DIY pocket emergency fire starter using a pen spring, two screws, a mini rocker switch, and an AA battery! We did it by mounting the spring heating coil to the switch and wiring it to the battery to create a windproof electric lighter. #diy #Tips #Lifehacks #idea

Tired of dead lighters? Build this windproof electric one! Stop wasting money on cheap lighters that always run out of fluid! Let me show you how to easily build a powerful pocket sized emergency fire starter using items you already have. Start by completely disassembling a standard clickable pen to extract the small metal spring hidden inside. Next, grab two small metal screws. Carefully thread the ends of the pen spring onto both screws, stretching the middle to create an exposed heating coil. Apply a drop of hot glue to the bottom of both screws and mount them upright onto a mini red rocker switch. Now take an ordinary AA battery, strip a green wire, glue the bare copper directly to the top positive terminal, and solder the other end to the back pin of your switch. Solder a short orange jumper wire between the other switch terminal and the first metal screw. Finally, take a blue wire, glue one end firmly to the bottom negative terminal of the battery, and wrap the exposed copper tightly around the second screw to complete the circuit. Flick the switch and the coil instantly glows red hot, igniting paper even in the wind. Comment lighter for more hacks.

We built a DIY bushcraft survival candle using a thick tree branch, twine, and natural pine resin! We did it by splitting the branch into quarters, hollowing out the top core, and packing it with resin and a coated twine wick to create a wind-resistant torch. #diy #Tips #Lifehacks #idea

Watch how this basic branch becomes a powerful survival candle. Stop relying on expensive store bought gear and let me show you how to easily craft a long lasting bushcraft candle using only natural materials you find in the woods. Start by sawing off a small piece of a thick tree branch. Use a heavy knife to carefully split this log directly down the middle into 4 equal quarters. Next, take your knife and shave off the inside corners of all four pieces, but only go about halfway down the length. When you fit the four pieces back together, the top half will form a deep hollow cup while the solid bottom holds it securely. Wrap a piece of twine tightly around the middle using a strong knot to lock the wood firmly in place. Trim the excess string and save a few strands to use as a Wick. Go find some sticky, highly flammable pine resin from a nearby tree. Coat your makeshift twine Wick in the resin, then pack the rest of the hollow core completely full of this amazing natural sap. Bury your Wick deep inside, leaving just the tip exposed. Light it up and you instantly have a brilliant wind resistant survival torch. Comment survive for more.

We built a DIY pocket-sized electric arc generator packed inside a sleek carbon fiber tube! We did it by wiring a 1000kV pulse generator with rechargeable lithium batteries, switches, and metal prongs sealed in epoxy resin. #diy #Tips #Lifehacks #idea

Watch me pack 1 million volts into this tiny tube. Let me show you exactly how to build this incredible pocket sized electric arc generator at home using basic electronics. Start by grabbing a durable black plastic tube to act as your main casing. You will need a 1,000 kilovolt pulse generator, a tiny lithium charging module, three micro batteries, a small red push button, and a main power switch. First, carefully solder your three lithium batteries together, then wire them directly into the charging board. Next, integrate the bottom switch and the side button into your circuit to give you complete control over the power release. Slide all these internal electronics carefully into your plastic tube. Use strong glue to mount the red button on the side and secure the charging port and switch flush at the bottom. To safely insulate everything, mix some epoxy resin and pour it into the base until it hardens completely. Solder two metal prongs to the top wires, add plastic supports, and wrap the tube in sleek carbon fiber vinyl. Turn it on, press the button, and watch the massive electrical arc. Comment shock for more hacks.

We built a DIY pocket-sized spot welder using a 9V battery, two metal screws, copper wire, and a rocker switch! We did it by wiring the battery terminals to the screws through the switch, creating an intense electrical arc capable of welding metal in seconds. #diy #Tips #Lifehacks #idea

Stop overpaying for expensive welding tools. I'm going to show you how a simple 9 volt battery and two screws can melt solid metal in seconds. Let's build a pocket sized spot welder. Start by grabbing a standard 9 volt battery. Use a sharp utility knife to carefully scratch and clean in both top terminals, ensuring a perfect electrical connection. Next, take a small red rocker switch, apply a thick drop of hot glue and mount it firmly to the side of your battery. Flip the battery upside down, apply hot glue to the bottom, and attach two long metal screws, making sure they stay perfectly straight and parallel. Take a short piece of bare copper wire, solder one end to the negative terminal, and loop the other end tightly around the first pin of your switch. Use a second copper wire to connect the other switch pin directly to the first metal screw. Finally, grab a blue insulated wire, soldier it to the positive terminal, and wrap the bare end securely around the threads of the second screw. Your tool is ready. Touch the screws to a metal hinge, press the switch, and watch it instantly create an intense electrical arc that flawlessly welds the pieces together. Comment weld.

We built a DIY pocket-sized wood engraver using an AA battery, safety pin prongs, copper wiring, and pencil graphite! We did it by wiring a rocker switch and wedging graphite between the prongs to make it glow red-hot enough to burn wood. #diy #Tips #Lifehacks #idea

This tiny battery gets dangerously hot enough to actually burn wood. Let me show you how to build a surprisingly powerful pocket sized engraver using simple items you already own. Start by grabbing a metal safety pin. Use a sharp utility knife to carefully snap off the pointed tip, leaving you with two straight metal prongs. Next, take a standard wooden pencil and cut off the back end right below the metal eraser ferrule. Pull out the eraser and insert your two metal prongs directly into that empty metal cup. Use a drop of hot glue to secure them tightly in place. Now grab an ordinary AA battery, apply hot glue to the top positive terminal, and mount the metal pencil piece right on top. Take a small rocker switch and attach a looped copper wire to one of its pins. Glue this switch securely to the bottom negative terminal of your battery. Run a wire from the other switch pin all the way up to the top. Tightly wrap the bare copper end around both metal prongs. Finally, wedge a tiny piece of pencil graphite between the prongs. Press the switch and the graphite instantly glows red hot. Ready to engrave wood? Comment burn.

We built a simple orange-powered generator using a halogen bulb, copper coils, metal screws, and salt water! We did it by injecting saltwater electrolyte into the fruit and dipping a connected wire screw into the solution, triggering a reaction that lights up the bulb.  #diy #Tips #Lifehacks #idea

Did you know you can generate electricity using just an orange and saltwater? Start by taking a small orange and firmly pressing a halogen car bulb directly into the top. Next, grab a piece of thick, bare copper wire. Use a lighter to heat it, then bend it into a tight coil. Carefully insert both ends of this copper coil into the orange, making sure it makes contact with the metal base of the bulb. Now take a metal screw and twist it straight into the side of the fruit. Grab a short piece of insulated wire and strip both ends to expose the copper. Wrap one end tightly around the screw in the orange and attach the other end to a second, separate screw. To create your electrolyte solution, pour kitchen salt into a glass jar, add water and stir it well. Use a plastic syringe to extract the salt water and inject it straight into the orange. Insert a third screw into the orange. Finally, dip that loose second screw into your jar of salt water. This instantly creates a powerful chemical reaction, fully lighting up the bulb. Comment power!

We built a functional DIY magnetic web shooter using a Pilot G2 pen barrel, a spring, a tiny magnet, and face mask ear loop string! We did it by assembling a spring-loaded magnetic launcher inside the disassembled pen casing, letting you shoot magnetic webs straight onto any metal surface. #diy #Tips #Lifehacks #idea

Ever dreamed of being Spider Man and swinging around your room? You can actually build your own functional web shooter using just a Pilot G2 pen and a medical face mask. Start by completely disassembling your pen, carefully extracting all the internal parts, including the metal spring and the black plastic clicker. Next, grab a blue medical mask and cut off one of the elastic ear loops. Carefully pull away the outer elastic shell to reveal the strong white fabric string hidden inside. Now grab a tiny, powerful magnet. Thread your white string directly through the small black plastic clicker piece. Use a drop of hot glue to attach the magnet securely to the very tip. Slide the metal spring onto the string right behind that plastic piece. Assemble a T shaped handle using the pen clips and wrap a small rubber band tightly around it. Hot glue the loose end of your string directly to the outside of this handle to load your gadget. Drop the entire mechanism into the top of the pen barrel. Use the empty ink cartridge to firmly push it down until it locks safely in place. Just press the trigger to instantly launch your magnetic web onto any metal fridge. Comment web for more hacks!

We built a powerful DIY mini spot welder using an old car spark plug, a battery graphite rod, and USB power! We did it by connecting the graphite-loaded spark plug to a power bank, generating intense localized heat to flawlessly weld metal blades together. #diy #Tips #Lifehacks #idea

Stop paying for expensive soldering irons or spot welders. You can easily build a powerful DIY mini spot welder at home using just an old spark plug and a dead battery. Start by grabbing a dead AA battery. Use a utility knife to carefully peel away the metal casing and extract the solid black graphite rod from the center. Next, take a standard pencil sharpener and gently shave the tip of the graphite rod until it is perfectly sharp and pointed. Grab an old car spark plug and insert the sharpened graphite rod straight into the top terminal. Take a piece of orange wire, strip the ends, and wrap the bare copper tightly around the base of the graphite rod to secure it. Now take an old USB cable and cut the end off to expose the internal wires. Twist your orange wire onto one of the USB wires and attach a new yellow wire to the other to power your tool. Simply plug the USB cable directly into a standard portable power bank to use it. Attach the yellow wire to your first piece of metal and press the graphite tip firmly against the second piece. The circuit instantly generates intense heat, flawlessly welding the metal blades together. Save this video and comment weld for more.

We built a compact DIY electric fire starter using a simple AA battery, wires, a rocker switch, and a metal nail! We did it by connecting the battery through the switch to create a hot electric arc with a second nail, instantly igniting paper into a flame. #diy #Tips #Lifehacks #idea

Stop wasting money on cheap, unreliable lighters. Did you know you can easily build your own powerful DIY electric fire starter using just a simple AA battery and a metal nail? Start by grabbing a standard nail, use a file to score the center, and carefully snap the sharp tip off. Next, take a standard AA battery and apply a thick drop of hot glue directly to the top positive terminal. Firmly attach the flat bottom of your cut nail onto the glue, holding it perfectly upright until it dries. Next, grab a small red rocker switch. Take a short piece of orange wire, strip the plastic ends to expose the bare copper, and tightly twist one side into a small circular loop. Attach this copper loop securely to the first metal pin on the switch. Apply a solid drop of hot glue to the bottom negative terminal of your battery and firmly mount the switch. Now strip both ends of a second piece of orange wire, attach one end to the second switch pin, and tightly wrap the other bare end directly around the metal base of the top nail. To use it, press a second uncut nail against both the top nail and the wrapped copper wire while pressing the switch. This instantly creates a super hot electrical arc, igniting tissue paper into a blazing flame. Comment fire for more hacks.

We built a pocket-sized DIY mini shooter using simple items like an empty pen, a rubber band, and a safety pin! We did it by attaching a rubber band trigger mechanism with a safety pin latch to launch ink refill cartridges with enough power to pop balloons. #diy #Tips #Lifehacks #idea

Stop throwing away your empty pens! Did you know you can easily transform them into a surprisingly powerful pocket sized mini shooter that actually pops balloons? Start by grabbing a standard pen, remove the outer cap, and simply unscrew the front tip completely. Use a sharp utility knife to carefully slice off the closed back end of the clear plastic barrel, creating a fully open tube. Next, take a small plastic plug, apply a thick drop of hot glue, and firmly attach it directly to the pocket clip of your pen cap. Slice off the narrow top of the pen cap to completely open it up, slide this modified cap tightly onto the back end of the clear barrel. Now take a rubber band and cut it in half. Tie it securely to the circular loop of a metal safety pin, and carefully use a lighter to slightly melt the knot so it never slips under tension. Tie the two loose ends of the rubber band tightly around the front of the clear barrel, right over the textured rubber grip to load your new shooter. Grab an ink cartridge from another pen and slide it straight into the barrel. Pull the safety pin back, hook it securely onto that glued plug to lock the cartridge safely in place. Take your aim and release the pin to shoot. Comment shoot for more.

We crafted a waterproof, windproof DIY survival fire starter using standard matches, a striker strip, paper, thread, and melted candle wax! We did it by bundling the matches inside the striker strip with a pull string, wrapping and thread-binding it, then dipping the whole bundle in hot wax so pulling the string ignites it instantly. #diy #Tips #Lifehacks #idea

Stop buying expensive survival matches! Did you know you can easily build your own ultimate waterproof and windproof emergency fire starter at home? Start by cutting the brown striking strip off a standard matchbox, stick it directly onto a small piece of tape. Grab a short loop of string and attach it to the edge. Now place exactly six matches onto the tape so all their heads are touching the striker, and tightly roll the tape around them. Next, take a piece of toilet paper and completely wrap it around the matches, leaving only your string loop exposed at the top. Use black thread to tightly bind the paper so it never unravels. Now chop up a regular paraffin wax candle, place the wax chunks into an empty metal tin and heat it until it melts into a clear liquid. Grab your bundle by the string and fully submerge it into the hot wax. Let it dry and you've built a flawless survival torch. To use it, just yank the string hard. The internal friction instantly ignites the matches and the wax fuels a massive windproof flame. Comment fire for more.

We built a DIY mini cannon bottle cap attachment using plastic caps, a pen tube, and a electronic lighter igniter! We did it by sealing the components, spraying aerosol inside an empty bottle for fuel, and clicking the igniter to launch a paper wad. #diy #Tips #Lifehacks #idea

Stop throwing away your empty water bottles. You can easily turn them into a powerful DIY mini cannon using a simple lighter. Start by grabbing the plastic caps off two standard bottles. Apply a ring of strong liquid glue to the top of one cap and firmly press the second cap against it so they are joined back to back. Next, dismantle an old electronic lighter to extract the internal spark mechanism. Grab a marker, draw two dots on your glued caps and carefully cut out two small holes. Take a short plastic pen tube and insert it into the first hole. Push the lighter spark mechanism into the second hole, ensuring the wire sits inside. Apply super glue around the outside edges to secure both pieces. Flip the caps over and fill the inside gaps with hot glue to create a perfect airtight seal. Glue the lighter's plastic lever onto the igniter to act as your firing button. To load, push a tiny paper wad into the pen tube, spray a quick burst of aerosol into the cap, screw it onto an empty bottle and press to launch. Comment shoot!

We turned an old yellow lighter into a spring-loaded mini arrow shooter that actually pops balloons! We did it by modifying the inner housing with a wire catch and spring, loading a toothpick arrow, and pressing the lever to launch. #diy #Tips #Lifehacks #idea

Stop throwing away your empty lighters! Did you know you can easily convert them into a powerful spring loaded mini arrow shooter? Let's build a pocket sized gadget that actually pops balloons! Start by removing the top metal guard and pulling out the spark wheel to extract the black plastic housing. Thread a tiny piece of blue wire straight through the side holes of this housing, trimming the excess to create a locking catch. Use a utility knife to carefully slice off the very top section of the plastic mount. Use a metal screw to widen the inside, then drop the small spring back in. Insert a blue plastic tube directly into the lighter's main body. Apply hot glue to the top prongs and securely remount your modified black housing. Snap the metal guard back on and slide an orange cap over the gas lever. Now grab a wooden toothpick, slice a tiny slit in the tip, and insert a sharp paper arrow head. Firmly push your arrow straight down into the housing until it safely locks under that blue wire. Simply press the orange lever to lift the catch and instantly launch your arrow. Comment shoot!

We built a DIY electric arc lighter using an AA battery, two copper nails, and a ballpoint pen spring! We did it by wiring the spring across the nails inside the pen barrel to create an instant red-hot heating element. #diy #Tips #Lifehacks #idea

Bored at home? Stop throwing away your empty lighters! You can easily transform them into a genius mini flaming crossbow in just seconds! Start by grabbing two standard lighters. Use a sharp utility knife to carefully cut one lighter in half at a slight downward angle. Apply a thick drop of hot glue directly to the cut edge and firmly attach it to the side of your second lighter to create an ergonomic pistol grip. Next, take a metal paper clip and bend it into a small bow shape with circular loops on the outer ends and a tiny guide loop in the center. Cut a small rubber band in half and tie the ends tightly to those outer paperclip loops to create your elastic bowstring. Apply hot glue to the front nozzle of your main lighter and securely mount the paperclip bow. Then grab a small binder clip and glue it directly behind the bow to act as your firing trigger. To load it, pull the rubber band back and lock it safely inside the opened binder clip. Jaws slide a standard matchstick straight through the center guide loop, strike the lighter to ignite the tip, and press the clip to launch your flaming arrow. Save this video, comment. Shoot.